Activity for GeigerLog

Arvi Hakanen modified a comment on discussion General Discussion

Arvi Hakanen — Fri, 04 Sep 2026 04:39:03 -0000

How can I start GeigerLog with Audio Counter activated? - I found the answer to the question in the GeigerLog-Manual: Configuration

Arvi Hakanen posted a comment on discussion Gamma Spectra in GeigerLog

Arvi Hakanen — Thu, 03 Sep 2026 05:05:46 -0000

Thanks!

ullix posted a comment on discussion Gamma Spectra in GeigerLog

ullix — Wed, 02 Sep 2026 09:05:31 -0000

You did not provide much info. I can only guess that you missed activation of your device? Read the chapter Configuration of GeigerLog in the GeigerLog manual. Also: please post in the appropriate forum! You posted in the Gamma Spectra forum, which surely is not the place for questions on Audio counters. I will delete your post in a few days. If you still have questions, post again at a better place!

Arvi Hakanen posted a comment on discussion Gamma Spectra in GeigerLog

Arvi Hakanen — Tue, 01 Sep 2026 12:47:13 -0000

How can I start GeigerLog with AudioCounter activated? I have a plastic scintillator made by Nano Smart Sensor...

Arvi Hakanen posted a comment on discussion General Discussion

Arvi Hakanen — Tue, 01 Sep 2026 11:25:04 -0000

How can I start GeigerLog with Audio Counter activated? 'Then from the menu choose: Device --> AudioCounter Series --> Show Extended Info. ' I see only GMC Series...

Tom Johnson posted a comment on discussion General Discussion

Tom Johnson — Sun, 26 Jul 2026 21:02:34 -0000

Thanks, That worked out.

ullix posted a comment on discussion General Discussion

ullix — Sun, 26 Jul 2026 09:00:32 -0000

A known problem which came up with Py3.14. It is fixed in latest GeigerLog pre-releases. Download the latest pre-release from here: https://sourceforge.net/p/geigerlog/discussion/devel2/ Currently the latest is pre08.

Tom Johnson posted a comment on discussion General Discussion

Tom Johnson — Sat, 25 Jul 2026 18:25:51 -0000

I installed the latest python 3.14.6 and GeigerLog 2.1 today. But when I run the geigerlog.bat I end up getting the following: File "C:\geigerlog\gsup_utils.py", line 375, in g.versions["sqlite3 module"] = sqlite3.version # = 2.6.0 ^^^^^^^^^^^^^^^ AttributeError: module 'sqlite3' has no attribute 'version' GeigerLog has finished Any help would be appriciated.

ullix modified a comment on discussion GeigerLog Development Versions

ullix — Sat, 04 Jul 2026 10:13:02 -0000

The main reason for this pre-release is the support of the new GMC-800Re2.00. This is not only a new firmware, but also new hardware, despite an unchanged name! This hardware makes it incompatible with previous versions of GeigerLog! And, by the way, makes it also incompatible with RadPro - what a coincidence that competing software can not be installed any more :-(( GeigerLog needed modest changes, but then faces some new problems: GeigerLog was too fast (!) for this latest, greatest microprocessor,...

ullix modified a comment on discussion GeigerLog Development Versions

ullix — Sat, 04 Jul 2026 10:12:14 -0000

ullix posted a comment on discussion GeigerLog Development Versions

ullix — Sat, 04 Jul 2026 10:08:40 -0000

ullix posted a comment on discussion GeigerLog Development Versions

ullix — Wed, 01 Jul 2026 08:20:05 -0000

Well. I conclude that everything is working as it should?

alexander posted a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 23:10:25 -0000

Ubuntu 26.04 LTS Pro: Playsound 1.2.2 and Python 3.14.3 work for me. for example I can hear a sound when I click the GeigerLog "Rad Pro" button to connect

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 14:52:19 -0000

Ubuntu 26.04 LTD Pro Guide sudo apt install python3-venv sudo apt install libportaudio2 ./GeigerLog.sh setup The GeigerLog setup installs only the old minimum required versions of the packages manually install the five missing packages without specifying a version, see pics

ullix posted a comment on discussion GeigerLog Development Versions

ullix — Tue, 30 Jun 2026 10:07:28 -0000

My OS used for GeigerLog is Ubuntu 25.04. Its default Python is 3.13.3. I have now added Python3.14.0 by installing from source code. Py3.14 allows a successful GeigerLog setupfor all LATEST pips, with the exception of playsound. Audio playing is a seemingly simple tasks, and there are multiple tools for it. Unfortunately, they all seem to have a flaw somewhere. playsound 1.3 does not work on Window, but 1.2.2 does. But 1.2.2 now does not play on Py3.14, and playsound 1.3 cannot be installed on Py3.14....

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:36:01 -0000

Ubuntu 26.04 LTD Pro Guide (1-3 commands from geigerlog manual) sudo apt install python3-venv sudo apt install libportaudio2 ./GeigerLog.sh setup The GeigerLog setup installs only the old minimum required versions of the packages manually install the five missing packages without specifying a version, see pics

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:34:37 -0000

Ubuntu 26.04 LTD Pro Guide (1-3 geigerlog manual) sudo apt install python3-venv sudo apt install libportaudio2 ./GeigerLog.sh setup The GeigerLog setup installs only the old minimum required versions of the packages manually install the five missing packages without specifying a version, see pics

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:33:49 -0000

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:30:26 -0000

I restored my Ubuntu 26.04 system using Timeshift to the state before I tried to install GeigerLog. If I modify geigerlog.py by changing it to Python 3.14, or use your modified version, the setup process with errors, video showing the issue. Unfortunately, I now also have the problem that even pip install numpy scipy matplotlib lxml simplepyble no longer works correctly, while now compile instead to use whl numpy. I suspect that during my earlier tests I had installed additional dependencies. NumPy...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:28:36 -0000

I restored my Ubuntu 26.04 system using Timeshift to the state before I tried to install GeigerLog. If I modify geigerlog.py by changing it to Python 3.14, or use your modified version, the setup process with errors, video showing the issue. Unfortunately, I now also have the problem that even pip install numpy scipy matplotlib lxml simplepyble no longer works correctly, as it hangs while now compile instead to use whl numpy. I suspect that during my earlier tests I had installed additional dependencies...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:27:08 -0000

I restored my Ubuntu 26.04 system using Timeshift to the state before I tried to install GeigerLog. If I modify geigerlog.py by changing it to Python 3.14, or use your modified version, the setup process with errors, video showing the issue. Unfortunately, I now also have the problem that even pip install numpy scipy matplotlib lxml simplepyble no longer works correctly, as it hangs while now compile instead to use whl numpy. I suspect that during my earlier tests I had installed additional dependencies...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:25:50 -0000

I restored my Ubuntu 26.04 system using Timeshift to the state before I tried to install GeigerLog. If I modify geigerlog.py by changing it to Python 3.14, or use your modified version, the setup process starts, but the errors remain exactly the same. Here is a video showing the issue. Unfortunately, I now also have the problem that even pip install numpy scipy matplotlib lxml simplepyble no longer works correctly, as it hangs while now compile instead to use whl numpy. I suspect that during my earlier...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:24:37 -0000

I restored my Ubuntu 26.04 system using Timeshift to the state before I tried to install GeigerLog. If I modify geigerlog.py by changing it to Python 3.14, or use your modified version, the setup process starts, but the errors remain exactly the same. Here is a video showing the issue. ChatGPT's analysis of the NumPy error shown in the video Unfortunately, I now also have the problem that even pip install numpy scipy matplotlib lxml simplepyble no longer works correctly, as it hangs while now compile...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:20:57 -0000

I restored my Ubuntu 26.04 system using Timeshift to the state before I tried to install GeigerLog. If I modify geigerlog.py by changing it to Python 3.14, or use your modified version, the setup process starts, but the errors remain exactly the same. Here is a video showing the issue. Unfortunately, I now also have the problem that even pip install numpy scipy matplotlib lxml simplepyble no longer works correctly, as it hangs while now compile instead to use whl numpy. I suspect that during my earlier...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:17:49 -0000

GeigerLog.py currently contains an entry that makes it impossible to install under Ubuntu 26.04 LTS Pro, since Ubuntu now uses Python 3.14. supPythons = ["python3.13", "python3.12", "python3.11", "python3.10"] after editing to python3.14setup starts In addition, several extra packages have to be manually installed before the setup can complete successfully, because the GeigerLog setup has problems installing them pip install numpy scipy matplotlib lxml simplepyble I am just an ordinary user, and...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:16:20 -0000

GeigerLog.py currently contains an entry that makes it impossible to install under Ubuntu 26.04 LTS Pro, since Ubuntu now uses Python 3.14. supPythons = ["python3.13", "python3.12", "python3.11", "python3.10"] In addition, several extra packages have to be manually installed before the setup can complete successfully, because the GeigerLog setup has problems installing them pip install numpy scipy matplotlib lxml simplepyble I am just an ordinary user, and I only managed to get it working with the...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:14:14 -0000

GeigerLog.py currently contains an entry that makes it impossible to install under Ubuntu 26.04 LTS Pro, since Ubuntu now uses Python 3.14. supPythons = ["python3.13", "python3.12", "python3.11", "python3.10"] after editing to python3.14 In addition, several extra packages have to be manuell installed before the setup can complete successfully. pip install numpy scipy matplotlib lxml simplepyble I am just an ordinary user, and I only managed to get it working with the help of ChatGPT. I couldn't...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:13:03 -0000

GeigerLog.py currently contains an entry that makes it impossible to install under Ubuntu 26.04 LTS Pro, since Ubuntu now uses Python 3.14. supPythons = ["python3.13", "python3.12", "python3.11", "python3.10"] In addition, several extra packages have to be installed before the setup can complete successfully. pip install numpy scipy matplotlib lxml simplepyble I am just an ordinary user, and I only managed to get it working with the help of ChatGPT. I couldn't find any information about this in the...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:12:47 -0000

GeigerLog.py currently contains an entry that makes it impossible to install under Ubuntu 26.04 LTS Pro, since Ubuntu now uses Python 3.14. supPythons = ["python3.13", "python3.12", "python3.11", "python3.10"] supPythons = ["python3.13", "python3.12", "python3.11", "python3.10"] In addition, several extra packages have to be installed before the setup can complete successfully. pip install numpy scipy matplotlib lxml simplepyble I am just an ordinary user, and I only managed to get it working with...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:12:08 -0000

GeigerLog.py currently contains an entry that makes it impossible to install under Ubuntu 26.04 LTS Pro, since Ubuntu now uses Python 3.14. supPythons = ["python3.13", "python3.12", "python3.11", "python3.10"] In addition, several extra packages have to be installed before the setup can complete successfully. pip install numpy scipy matplotlib lxml simplepyble I am just an ordinary user, and I only managed to get it working with the help of ChatGPT. I couldn't find any information about this in the...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:09:38 -0000

GeigerLog.py currently contains an entry that makes it impossible to install/start under Ubuntu 26.04, since Ubuntu now uses Python 3.14. pip install numpy scipy matplotlib lxml simplepyble In addition, several extra packages have to be installed before the setup can complete successfully. pip install numpy scipy matplotlib lxml simplepyble I am just an ordinary user, and I only managed to get it working with the help of ChatGPT. I couldn't find any information about this in the installation guide...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:09:08 -0000

GeigerLog.py currently contains an entry that makes it impossible to install under Ubuntu 26.04, since Ubuntu now uses Python 3.14. pip install numpy scipy matplotlib lxml simplepyble In addition, several extra packages have to be installed before the setup can complete successfully. pip install numpy scipy matplotlib lxml simplepyble I am just an ordinary user, and I only managed to get it working with the help of ChatGPT. I couldn't find any information about this in the installation guide or anywhere...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:08:27 -0000

GeigerLog.py currently contains an entry that makes it impossible to install under Ubuntu 26.04, since Ubuntu now uses Python 3.14. supPythons = ["python3.13", "python3.12", "python3.11", "python3.10"] In addition, several extra packages have to be installed before the setup can complete successfully. pip install numpy scipy matplotlib lxml simplepyble I am just an ordinary user, and I only managed to get it working with the help of ChatGPT. I couldn't find any information about this in the installation...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:07:49 -0000

Thanks, i deleted the venv. Result with ./GeigerLog.sh setup latest: everything was installed xcept for playsound playsound is effectively broken on modern Python (especially 3.13/3.14+) The clean fix is to switch to simpleaudio or pygame

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:07:10 -0000

Thanks, i deleted the venv. Result with ../GeigerLog.sh setup latest: everything was installed xcept for playsound playsound is effectively broken on modern Python (especially 3.13/3.14+) The clean fix is to switch to simpleaudio or pygame

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:03:14 -0000

Ubuntu 26.04 LTD Pro Guide sudo apt install python3-venv sudo apt install libportaudio2 ./GeigerLog.sh setup (The GeigerLog setup installs only the old minimum required versions of the packages) manually install the five missing packages without specifying a version, see pics

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 08:02:59 -0000

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 07:53:45 -0000

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 07:53:26 -0000

Ubuntu 26.04 LTD Pro Guide sudo apt install python3-venv sudo apt install libportaudio2 ./GeigerLog.sh setup ( The GeigerLog setup installs only the old minimum required versions of the packages) manually install the five missing packages without specifying a version, see pics

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:35:15 -0000

Ubuntu 26.04 LTD Pro Guide sudo apt install python3-venv sudo apt install libportaudio2 ./GeigerLog.sh setup manually Install the 5 missing packages, see pics

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:24:39 -0000

I restored my Ubuntu 26.04 system using Timeshift to the state before I tried to install GeigerLog. If I modify geigerlog.py by changing it to Python 3.14, or use your modified version, the setup process starts, but the errors remain exactly the same. Here is a video showing the issue. Unfortunately, I now also have the problem that even pip install numpy scipy matplotlib lxml simplepyble no longer works correctly, as it hangs while now compile instead to use whl numpy. I suspect that during my earlier...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:23:46 -0000

I restored my Ubuntu 26.04 system using Timeshift to the state before I tried to install GeigerLog. If I modify geigerlog.py by changing it to Python 3.14, or use your modified version, the setup process starts, but the errors remain exactly the same. Here is a video showing the issue. Unfortunately, I now also have the problem that even pip install numpy scipy matplotlib lxml simplepyble no longer works correctly, as it hangs while now compile instead whl numpy. I suspect that during my earlier...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:22:13 -0000

I restored my Ubuntu 26.04 system using Timeshift to the state before I tried to install GeigerLog. If I modify geigerlog.py by changing it to Python 3.14, or use your modified version, the setup process starts, but the errors remain exactly the same. Here is a video showing the issue. Unfortunately, I now also have the problem that even pip install numpy scipy matplotlib lxml simplepyble no longer works correctly, as it hangs while now compile numpy. I suspect that during my earlier tests I had...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:19:39 -0000

I restored my Ubuntu 26.04 system using Timeshift to the state before I tried to install GeigerLog. If I modify geigerlog.py by changing it to Python 3.14, or use your modified version, the setup process starts, but the errors remain exactly the same. Here is a video showing the issue. Unfortunately, I now also have the problem that even pip install numpy scipy matplotlib lxml simplepyble no longer works correctly, as it hangs while installing numpy. I suspect that during my earlier tests I had installed...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:13:14 -0000

This is an iMac with an Intel processor (I own three of them). They run only Ubuntu 26.04 LTS Pro and, depending on iMac, either Windows 11 25H2 or Windows 10 IoT Enterprise (supported until 2032) in a dual-boot setup, i removed macOS from iMacs as they no longer receive macOS updates. The Apple logo displayed under Ubuntu 26.04 LTS Pro is a custom logo. Ubuntu 26.04 LTS Pro is my primary operating system. I only use Win occasionally, when I need software that doesn't run on Linux I will, when I...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:12:11 -0000

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:10:00 -0000

Thanks, i deleted the venv. Result: everything was installed xcept for playsound playsound is effectively broken on modern Python (especially 3.13/3.14+) The clean fix is to switch to simpleaudio or pygame

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:09:05 -0000

Thanks, i deleted the venv. Result: everything was installed successfully except for playsound playsound is effectively broken on modern Python (especially 3.13/3.14+) The clean fix is to switch to simpleaudio or pygame

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:07:50 -0000

Ubuntu 26.04 LTD Pro Guide sudo apt install python3-venv sudo apt install libportaudio2 ./GeigerLog.sh setup manually Install the 5 missing packages, see pics

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:07:32 -0000

Ubuntu 26.04 LTD Pro Guide sudo apt install python3-venv sudo apt install libportaudio2 ./GeigerLog.sh setup manually Install the 5 missing packages, see pics

alexander posted a comment on discussion GeigerLog Development Versions

alexander — Tue, 30 Jun 2026 01:06:46 -0000

Ubuntu 26.04 Guide sudo apt install python3-venv sudo apt install libportaudio2 ./GeigerLog.sh setup manually Install the 5 missing packages, see pics

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Sun, 28 Jun 2026 10:19:55 -0000

Thanks, i deleted the venv. Result: everything was installed successfully except for playsound getgpt: This is a known kind of breakage with playsound + modern Python versions (especially 3.12+ / 3.13+ / 3.14-dev), and your traceback strongly suggests exactly that problem: OSError: could not get source code during build metadata extraction What’s actually happening playsound==1.3.0 is very old and poorly maintained. It relies on setuptools introspection during build. On newer Python versions (you’re...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Sun, 28 Jun 2026 10:11:01 -0000

alexander posted a comment on discussion GeigerLog Development Versions

alexander — Sun, 28 Jun 2026 10:10:24 -0000

Thanks, i deleted the venv. Result: everything was installed successfully except for ‘playsound getgpt: This is a known kind of breakage with playsound + modern Python versions (especially 3.12+ / 3.13+ / 3.14-dev), and your traceback strongly suggests exactly that problem: OSError: could not get source code during build metadata extraction What’s actually happening playsound==1.3.0 is very old and poorly maintained. It relies on setuptools introspection during build. On newer Python versions (you’re...

alexander modified a comment on discussion GeigerLog Development Versions

alexander — Sun, 28 Jun 2026 09:48:32 -0000

This is an older iMac with an Intel processor (I own three of them). They run only Ubuntu 26.04 LTS Pro and, depending on iMac, either Windows 11 25H2 or Windows 10 IoT Enterprise (supported until 2032) in a dual-boot setup, i removed macOS from iMacs as they no longer receive macOS updates. The Apple logo displayed under Ubuntu 26.04 LTS Pro is a custom logo. Ubuntu 26.04 LTS Pro is my primary operating system. I only use Windows occasionally, when I need software that doesn't run on Linux I will,...

ullix posted a comment on discussion GeigerLog Development Versions

ullix — Sun, 28 Jun 2026 09:47:32 -0000

I tested updating all pip-stuff to their latest version. In my case, using Python3.13, it works. Your-mileage-may-vary! To do this is simple: delete all __venv * files inside the GeigerLog working directory. Then start GL with this command: ./GeigerLog.sh setup latest then start GL with: ./GeigerLog.sh -d If it works, then the "-d" option should result in a file geigerlog.proglog.develin the data directory. Please, post this file.

alexander posted a comment on discussion GeigerLog Development Versions

alexander — Sun, 28 Jun 2026 09:46:16 -0000

This is an older iMac with an Intel processor (I own three of them). They run only Ubuntu 26.04 LTS Pro and, depending on iMac, either Windows 11 25H2 or Windows 10 IoT Enterprise (supported until 2032) in a dual-boot setup, as they no longer receive macOS updates. The Apple logo displayed under Ubuntu 26.04 LTS Pro is a custom logo. Ubuntu 26.04 LTS Pro is my primary operating system. I only use Windows occasionally, when I need software that doesn't run on Linux I will, when I have the time and...

ullix posted a comment on discussion GeigerLog Development Versions

ullix — Sun, 28 Jun 2026 09:04:23 -0000

I am confused: your screenvideo shows an apple logo - so do you have Ubuntu installed on a Mac? As solo- or dual-boot? I had no idea this is even possible??? Why not install GeigerLog directly on the Mac? As long as numpy & friends is not properly installed, GeigerLog will not run. In this moment I can't tell whether numpy & al. is not updated enough to suppport Py3.14, or Py3.14 does not support those versions of numpy any more. Release notes do not tell. Allowing always the latest version of any...

alexander posted a comment on discussion GeigerLog Development Versions

alexander — Sun, 28 Jun 2026 01:22:48 -0000

I restored my Ubuntu 26.04 system using Timeshift to the state before I tried to install GeigerLog. If I modify geigerlog.py by changing it to Python 3.14, or use your modified version, the setup process starts, but the errors remain exactly the same. Here is a video showing the issue. Unfortunately, I now also have the problem that even pip install numpy scipy matplotlib lxml simplepyble no longer works correctly, as it hangs while installing numpy. I suspect that during my earlier tests I had installed...

ullix posted a comment on discussion GeigerLog Development Versions

ullix — Sat, 27 Jun 2026 07:37:20 -0000

Thanks for reporting. You did find the cause for the problem. I am attaching an updated version of the responsible file. Please, just copy over the existing file! I do not understand the requirement to manually install your "other" packages; this should have been taken care of by GeigerLog's "setup" command. Perhaps a follow-up problem of the first issue? If you can, please delete your "venv*" folder and re-run setup; report any issues. Nice achievement using ChatGPT! Could you post the questions/command...

alexander posted a comment on discussion GeigerLog Development Versions

alexander — Fri, 26 Jun 2026 21:53:26 -0000

ullix modified ticket #12

ullix — Sun, 21 Jun 2026 08:19:16 -0000

SyntaxError (gsup_utils.py)

ullix modified ticket #10

ullix — Sun, 21 Jun 2026 08:18:22 -0000

MacOS not supported by v2.0.0 - portNo variable used but unassigned

ullix modified ticket #11

ullix — Sun, 21 Jun 2026 08:17:27 -0000

RadPro is undetectable in Mac/Linux

ullix modified ticket #13

ullix — Sun, 21 Jun 2026 08:16:11 -0000

Ne se lance pas

ullix modified ticket #14

ullix — Sun, 21 Jun 2026 08:15:18 -0000

GeigerLog does not detect a GMC-800 device with Rad Pro firmware

ullix posted a comment on discussion General Discussion

ullix — Sun, 21 Jun 2026 08:12:36 -0000

Good to hear that GeigerLog is running well! A reminder: the latest version of GeigerLog - as a pre-release - can always be found here: https://sourceforge.net/p/geigerlog/discussion/devel2/

Gorit Maqueda posted a comment on discussion General Discussion

Gorit Maqueda — Sat, 20 Jun 2026 17:34:49 -0000

Forget about it. I had installed Python 3.13.14 but, for some reason, I also installed Python 3.14, and that caused a mess. I cleaned all the stuff, re-installed 3.13.14 and now GeigerLog is happily set up and running. My apologies and thanks for reading this!

Gorit Maqueda posted a comment on discussion General Discussion

Gorit Maqueda — Sat, 20 Jun 2026 09:01:35 -0000

Hello! I've just installed GeigerLog on my Windows 11 PC and configured it as stated in the manual. I've installed Python, pip, etc. After running GeigerLog.bat, I get this: GeigerLog Startup -------------------- in RUNTIME mode --------------------------- startup: Command Line: ['geigerlog.py'] startup: System Python: Python 3.13.14 startup: Virtual Environment: venv found: __venv2.1pre01 startup: Virtual Environment: venv uses: Python 3.13.14 startup: Completed: Handing control to GeigerLog Runtime...

ullix posted a comment on discussion GeigerLog Development Versions

ullix — Thu, 11 Jun 2026 11:00:23 -0000

Thx for reporting the linecolor bug. Attached files are needed for a fix; please copy over the existing files.

Michel posted a comment on discussion GeigerLog Development Versions

Michel — Wed, 10 Jun 2026 19:00:23 -0000

Thanks for the new pre-release. It works fine with the RadPro on the GMC-800. One observation: The settings of the linecolor in geigerlog.cfg seems to have no effect. I configured the following linecolors: # linecolor: # A list with the colors for the twelve variables shown in the main graph. # # Options: A comma separated list of EXACTLY 12 proper color names. For color names see: # https://matplotlib.org/stable/gallery/color/named_colors.html # Note that alternatively you can put down the colors...

ullix posted a comment on ticket #14

ullix — Wed, 10 Jun 2026 09:02:40 -0000

I have uploaded v2.2pre07: https://sourceforge.net/p/geigerlog/discussion/devel2/

ullix posted a comment on discussion GeigerLog Development Versions

ullix — Wed, 10 Jun 2026 08:59:20 -0000

The main new feature in this pre-release is the support of RadPro on GQ's GMC-800 counter. Keep in mind that installing RadPro on this GMC counter requires overwriting its factory firmware! The GeigerLog configuration file custom.cfg has only this entry: [GMC_Device] GMC_Activation = yes [RadProDevice] RadProActivation = yes RadProVoltageDefault = off Modify it according to your needs, following the template in file geigerlog.cfg. It is recommended to NOT change the file geigerlog.cfg!

ullix posted a comment on ticket #14

ullix — Wed, 10 Jun 2026 08:12:10 -0000

Sorry, another fault of mine. It is getting complex with multi-file changes. But it seems it is all working now? Time for another full pre-release? The chip is "unknown" because this info comes from RadPro - and there is none :-(. Looking at my own GMC-800 device I see all chip-labels being sanded off! It likely is a STM or clone, because this is what all currrent RadPro supported devices are. I doubt that the chip info cannot be seen by the firmware, so chances are it is also hidden with intend...

Michel posted a comment on ticket #14

Michel — Wed, 10 Jun 2026 06:36:35 -0000

I cannot see this menue. Am I looking at the wrong place (see attached screenshot)? I can see the runRadProCommand() in gdev_radpro.py (and I do start GL with -d option) By the way, what should be shown for the "unknown chip"? Connected Device: GQ GMC-800 Chip:unknown 'GQ GMC-800' Is this the MCU? If so, this seems a STM32 (but likely a clone...)

Michel posted a comment on ticket #14

Michel — Wed, 10 Jun 2026 06:20:59 -0000

I notice in your log that you have set custom values for tube sensitivities. I have never seen these values before, what are they based on? These are the RadPro 3.1.1 default values for the M4011. They are based on numerical simulations from RadLab: https://github.com/Gissio/radlab/tree/main The tube type can be selected in the Menue. A Source Compensation based on RadLab can also be selected. The GMC-800 had its original 1st calibration point at 98.6 (for up to 10 uSv/h). So a calibration factor...

Michel posted a comment on ticket #14

Michel — Wed, 10 Jun 2026 05:58:07 -0000

Thanks! This seems to work now. GeigerLog does not overwrite the HV profile when connecting.

ullix modified a comment on ticket #14

ullix — Tue, 09 Jun 2026 11:41:23 -0000

RadPro in GL now has an option to run a RadPro command. GL must have been started with option "-d". Then in the RadPro menu you find Run RadPro Terminal Command. E.g. Command 'GET deviceId' may print into the NotePad: ==== Run RadPro Command ========================================== Running Command: 'GET deviceId' 0 FNIRSI GC-01 (APM32F103CB) 1 Rad Pro 2.0.2 2 7907521b

ullix posted a comment on ticket #14

ullix — Tue, 09 Jun 2026 10:46:43 -0000

RadPro in GL now has an option to run a RadPro command. GL must have been started with option "-d". Then in the RadPro menu you find. E.g. Command 'GET deviceId' may print into the NotePad: ==== Run RadPro Command ========================================== Running Command: 'GET deviceId' 0 FNIRSI GC-01 (APM32F103CB) 1 Rad Pro 2.0.2 2 7907521b

ullix posted a comment on ticket #14

ullix — Tue, 09 Jun 2026 08:32:29 -0000

Your HV measurement is what it should be! I had elaborated on those measurements in my article https://sourceforge.net/projects/geigerlog/files/Articles/GeigerLog-Radiation-v1.1%28CAJOE%29-Support-v1.0.pdf/download see chapter §The Anode Voltage". The internal resistance of the HV Generator typically comes out near 20MOhm. I have not seen a counter with much lower internal resistance, not even in those old clunkers of counters! One easy test: Touch the terminals of the built-in and powered tube with...

ullix posted a comment on ticket #14

ullix — Tue, 09 Jun 2026 07:23:39 -0000

Michel posted a comment on ticket #14

Michel — Mon, 08 Jun 2026 20:09:16 -0000

Thanks for the update. It seems GeigerLog cannot understand the string "off" (default voltage settings are still send to the device): 08 21:01:07.835 ...198 EXCEPTION: RadProVoltageDefault setting: '{t}' >'could not convert string to float: 'OFF''< in file: gsup_config.py in line: 2151 See attached log file. Some additional observations: It seems the following two RadPro commands are obsolete in RadPro 3.1.1: https://github.com/Gissio/radpro/blob/main/docs/comm.md GET tubeConversionFactor GET tubeBackgroundCompensation...

ullix posted a comment on ticket #14

ullix — Mon, 08 Jun 2026 11:50:02 -0000

Attached an update. Make sure to copy over the existing same-name files!

ullix posted a comment on ticket #14

ullix — Mon, 08 Jun 2026 07:53:18 -0000

Thx, I looked at the details. Please, always start GL with the option "-d", i.e. command is: "./Geigerlog.sh -d". This will create a proglog file with important info. Post file geigerlog.proglog.devel . File TEST.csv: where does this come from? It is not from GL. Its content is weird, to say the least. Many data missing, and many multiple lines, identical in timestamp and other. This gives hundreds of lines with no information??? File TEST.logdb: Looks ok. Poisson test reveals some potential problems,...

Michel posted a comment on ticket #14

Michel — Mon, 08 Jun 2026 06:16:08 -0000

Attached are some history files from the same session --- from logging with GeigerLog, download with GeigerLog, and download with the RadPro tools. Some small time periods seem to work fine; others miss the data. On the anode voltage setting at startup/connection of the counter, it would be cool if this could be switched off in the config file. I think the GMC-800 may have a loosely regulated step-up converter and may not need this. My ~380 V measurement may include some artefacts, but measuring...

Michel posted a comment on ticket #14

Michel — Sat, 06 Jun 2026 08:10:34 -0000

I've set the HV profile in the counter to "Factory default" and removed the automatic call to setRadProVoltage in initRadPro() for now (since it always overwrites the "Factory default" ) : ### set the default Anode voltage dprint(defname, f"Set Anode Voltage to: {g.RadProVoltageDefault} V") setIndent(1) # setRadProVoltage(g.RadProVoltageDefault) setIndent(0) The Factory default seems: Tube PWM Frequency: 2500 Hz Tube PWM Duty Cycle: 16.3 % This gives 380 ... 400 V when measured with a 1 GOhm. These...

ullix posted a comment on ticket #14

ullix — Sat, 06 Jun 2026 07:15:22 -0000

Good News! Though I still see some flaws, and hope you can help: The reported Anode voltage of 380 V seems rather low. Do you know/remember what it had been und the GMC firmware? Are you able to measure the anode voltage - you need a DVM and a 1 GigaOhm resistor? The Chip-Type is likely wrong. Next time you have run the thing please start GL with: ./GeigerLog.sh -d and post file geigerlog.proglog.devel or if not found geigerlog.proglog. I am surprised to hear that even reading the history does work!...

Michel posted a comment on ticket #14

Michel — Fri, 05 Jun 2026 17:22:10 -0000

Thanks! This works (incl. e.g., reading the history from the device). ==== Connect RadPro Device ============================================================ Device 'RadPro' successfully connected ==== Device Mappings ================================================================== Mappings as configured in GeigerLog's configuration file: Device : CPM CPS CPM1st CPS1st CPM2nd CPS2nd CPM3rd CPS3rd Temp Press Humid Xtra ---------------------------------------------------------------------------------------...

ullix modified a comment on ticket #14

ullix — Fri, 05 Jun 2026 08:14:54 -0000

I realized that all GMC counters do show this: Manufacturer: None Product : USB Serial So, it could well be that RadPro missed, or failed setting these USB properties. Perhaps those CH340 chips don't allow modification by firmware code - I don't know. But I am now using "USB Serial" for pre-selecting the ports, and then test for RadPro responses on those ports. We'll see what happens. Attached is a new gdev_radpro.py. I expect it to work by just copying over the existing file.

ullix posted a comment on ticket #14

ullix — Fri, 05 Jun 2026 08:11:25 -0000

I realized that all GMC counters do show this: Manufacturer: None Product : USB Serial So, it could well be that RadPro missed, or failed setting these USB properties. Perhaps those chips don't allow modification by firmware code - I don't know. But I am now using "USB Serial" for pre-selecting the ports, and then test for RadPro responses on those ports. We'll see what happens. Attached is a new gdev_radpro.py. I expect it to work by just copying over the existing file.

Michel posted a comment on ticket #14

Michel — Thu, 04 Jun 2026 17:54:52 -0000

After some further checking with chatGPT :-) it may not necessarily be a MAC problem, since other connected USB devices do show a manufacturere/product in the system profiler. e.g.: Bus: 0 Device: 1 Vendor ID : 0x152d Product ID: 0x579 Manufacturer: Intenso Product : External USB-3.0 Serial : 201803071010F Class : 0 Speed : 4 But for the counter: ============================== Bus: 2 Device: 1 Vendor ID : 0x1a86 Product ID: 0x7523 Manufacturer: None Product : USB Serial Serial : None Class : 255...

Michel posted a comment on ticket #14

Michel — Thu, 04 Jun 2026 17:13:48 -0000

O.K., this seems getting more complicated, and I'm afraid, becomes a MAC speciality. To be sure: The GMC device does seem to be working fully with that RadPro firmware? Yes, it seems working proper. At least I have not observed any issues up to now. lsusb does not natively exist on a MAC. However, there are homebrew packages which enable a kind-of lsusb command by calling the system profiler. In my case, this gives for the device: USB 3.1 Bus: Location ID: 0x02000000 Connection Type: Built-in Driver:...

ullix posted a comment on ticket #14

ullix — Thu, 04 Jun 2026 15:48:24 -0000

Oh dear, yes, this can't work :-( Trying as GMCdeivce: of course, once you have overwritten the GMC firmware, you can't use the GMC commands anymore. So, this tells you that the firmware has in fact changed! To be sure: The GMC device does seem to be working fully with that RadPro firmware? The "getPortList" in line 5 shows the first problem: the MAC is hiding information which the USB does provide, and which I used to identify devices. Well, doesn't work because the info is not there. I can't test...

Michel created ticket #14

Michel — Thu, 04 Jun 2026 14:40:20 -0000

GeigerLog does not detect a GMC-800 device with Rad Pro firmware

Adam Szewczyk posted a comment on discussion Feature Request

Adam Szewczyk — Fri, 15 May 2026 16:39:32 -0000

No problem. Here are the python files.

ullix posted a comment on discussion Feature Request

ullix — Fri, 15 May 2026 07:16:31 -0000

Thanks. But there are so many changes that I can't really see what it is doing and what is should replace. Can you please create the final file?

Adam Szewczyk modified a comment on discussion Feature Request

Adam Szewczyk — Fri, 15 May 2026 05:50:41 -0000

With help of openai Codex I added MQTT and TLS support for this device to last RC of geigerlog. I'm posting it here in case if you want to take a look on this and maybe add to the mainline.

Adam Szewczyk modified a comment on discussion Feature Request

Adam Szewczyk — Fri, 15 May 2026 05:50:31 -0000

With help of openai Codex I was added MQTT and TLS support for this device to last RC of geigerlog. I'm posting it here in case if you want to take a look on this and maybe add to the mainline.